Protected: Fluid Flow and Mixing Simulation

Most of what happens inside a tank, an extruder, or a heat exchanger is invisible. You only see the result: a batch that is slightly off, a product that cools unevenly, a line that needs cleaning more often than it should. Conventional calculations often struggle to explain why, especially when the fluid is not water-like and its viscosity changes with the flow itself. This is where fluid flow and mixing simulation in COMSOL Multiphysics comes to your aid, which lets you “look inside” the equipment. Whether you are mixing pharmaceutical ingredients or extruding polymers, you can find the root-cause using simulations before a costly physical implementation.

  • 50

What the Model Gives You

Depending on your needs, the model combines the physics that matters for your process the most: how the fluid flows, how it heats or cools, and how ingredients mix and react. Because these effects are solved together, you can see how changing one of them, such as impeller speed or wall temperature, affects all the others.

And what do you get as a result? Fluid and machine parameters that help you judge performance, such as velocity, pressure, shear rate, temperature, and concentration, plus derived quantities such as mixing efficiency, residence time, and impeller power and torque. The model also shows where problems hide: dead zones where fluid barely moves, cold spots, or regions of excessive shear. Many of these are hard to measure inside running equipment, so having them gives you a competitive advantage and can reduce prototyping and redesign costs.

Why Non-Newtonian Fluids Make the Calculation Harder

Simulation can also handle non-Newtonian fluid behavior, which is extremely hard to predict with conventional methods. Non-Newtonian fluids are different from traditional water-like fluids because their viscosity is not constant. Sauces, doughs, paints, creams, and polymer melts are non-Newtonian: their viscosity depends on how fast they are being sheared. A shear-thinning fluid, for example, becomes less viscous as the shear rate rises, which is often described with a power-law model. Other fluids have a yield stress and do not flow at all until the stress passes a threshold.

For the numerical model, this makes the equations nonlinear: the shear rate is calculated from the velocity gradient, and the viscosity depends on that shear rate, so the viscosity becomes part of the solution instead of an input. Fortunately, we are well equipped to handle all of this in COMSOL Multiphysics.

Five COMSOL Resources to See It in Practice

The resources below show how this plays out in practice.

1. The COMSOL Mixer Module

Source: COMSOL Mixer Module

Start with COMSOL’s Mixer Module page to see what is possible with COMSOL. It is built for mixers and stirred tank reactors, batch or continuous, in the pharmaceutical, fine chemical, and food industries. It includes laminar and turbulent flow, multiphase flow with liquid surface tracking, a library of parameterized impeller and tank geometries, and a range of non-Newtonian fluid models.

2. Pasta extrusion: a worked non-Newtonian example

COMSOL pasta extrusion simulation
Source: COMSOL Application Library – Pasta Extrusion

This model from the COMSOL Application Library simulates dough moving through a screw extruder. It uses a power-law model with coefficients taken from measured viscosities at different temperatures, a lower shear-rate cutoff that keeps the viscosity finite at near-zero shear, and a frozen rotor study, a fast steady-state approximation of the rotating screw. The results show why these fluids are hard to predict. Viscous heating raises the temperature in high-shear regions. High viscosity in low-shear zones near the screw leads to poor mixing. The velocity is also uneven across the extrusion channels, which means different flow rates through different holes and potentially different product quality.

3. A validated model: scraped surface heat exchanger

Scraped surface heat exchanger simulation
Source: COMSOL – Simulation of a Dynamic Scraped Surface Heat Exchanger

Highly viscous fluids flow in a deep laminar regime, which means poor heat transfer and high-pressure losses. This ConAgra Foods paper builds a 3D nonisothermal model of a scraped surface heat exchanger and validates it against measurements on peanut butter and starch solutions.

4. Mixing in pharmaceutical reactors

Pharmaceutical reactor mixing simulation
Source: COMSOL – Modeling of Mixing-Sensitive Pharmaceutical Processes

In pharma, mixing can decide product quality. This Bristol-Myers Squibb paper explains how poor mixing can cause impurities and lower selectivity in reactions, and localized supersaturation and uncontrolled nucleation in crystallizations. It then uses simulation to study agitation rate, feed rate, and reactor configuration.

5. How Nestlé uses simulation in confectionery

Nestlé confectionery simulation
Source: COMSOL – The Sweet Side of Simulation at Nestlé

To finish with an industry view, this user story shows how engineers at Nestlé’s Product Technology Centre in York use COMSOL Multiphysics® for three processes: a chocolate depositor for candy bars, a wafer baking plate, and an extruder that cooks and sorts cereals.

From Reactive Fixes to Design-Led Decisions

Different industries, the same pattern: the fluid does something you would not guess, and a model shows it before it becomes a cost. Based on these results, our Professional Services team can help you develop your machines to get better results with fewer prototypes.

If you have a process where the flow is a question mark, we would be glad to talk.

Recommended Events

Recommended Posts

Machine Learning with MATLAB

Explore how MATLAB transforms the world of machine learning. Discover 5 areas where MATLAB can help solve diverse learning problems. From interactive apps to Simulink integration, we’ve got you covered.

Deep Learning with MATLAB

Today we are living in a renaissance of artificial intelligence, Machine Learning, and Deep Learning, and everyone wants to be a part of this movement. But the question is if you interested in using deep learning technology, where do you begin?

Power Electronics Control Design

Discover three areas where Power Electronics Control Design with Simulink can transform your engineering projects. Reduce project time by 50%, access thousands of electrical modeling components, and build and tune motor control algorithms with ease.